Carpenter – First Period

____ plans start at the finished floor elevation and stop at the ceiling.

An ____ line is used to show the non hidden shape edges.

A t-square is the best tool for ____.

On a print the abbreviation “BS” means ____.

On a print the abbreviation “TYP” means ____.

On a print the abbreviation “WA” means ____.

On a print the abbreviation “RO” means ____.

Of the following pencil types, which is the darkest and softest grade?

9B refers to the ____.

The effort arm length compared to the resistance arm length is considered a(n) ____ type of advantage of a lever.

If your length is 3600 mm and your height is 1200 mm, then your diagonal is ____ rounded to the closest millimeter?

A floor plan can include the following. Select all that apply (4/5)

An actual 5 ft wall measures 1.25 inches on an imperial print. The scale the print uses is ____ equals one foot.

A three point drawing is used to show objects as ____.

The 12% deposit on a circular saw is $21.48. What is the full price of the saw?

The length of a diagonal used to square a building 25 feet by 41 feet is ____ feet.

Which of the following are included on a roof plan? Select all that apply (4/5)

If not reinforced, a ____ joint is the weakest type of joint.

A joint that enables the horizontal and vertical movement between two adjacent but separate members is called a ____ joint.

The best definition of sub base is ____.

The best definition of sub grade is ____.

A stamped certification mark must be present on all materials used on a ____.

Concrete blocks are available in sizes based on ____ mm increments.

____ are available in sizes based on 200 mm increments.

What is the maximum slump allowed for a concrete footing?

The ____ allowed in a concrete footing is 150 mm.

A builder must first consult a plot plan during the ____.

Loads resulting from the occurrence of temperature changes are an example of a(n) ____ load.

Regular joists are floor joists that ____.

Driveways and sidewalks that endure freeze/thaw cycles should use ____ concrete.

On the PWF certification stamp “L/B P/C CCA 1101”, which letters and/or numbers identify the preservative used?

Compression is the opposite of ___.

A block used to align the form bottom is called a ____.

Which of the following are true about headers. Select all that apply (4/5)

A concrete slab on ____ foundation is thickest on the outside perimeter.

A telepost supporting a beam is an example of a ____ load.

The certifying agency for lumber in Canada is ____.

The purpose of edge forms used for concrete sidewalks are which of the following? Select all that apply (2/5)

For a building that is 8900 wide by 11500 long with a 3 ply beam of 45 mm LVL material centered on the width. The floor system is anchored using a ladder at the top of a 200mm thick foundation wall. The clear span of the joists that are butted together over the beam rounded to the nearest millimetre is ____.

The National Building Code includes information on the following. Select all that apply (4/5)

An anchor bolt must have a thickness of no less than ____ mm in the foundation wall for a floor attachment frame.

A(n) ____ must have a thickness of no less than 12 mm in the foundation wall for a floor attachment frame.

To identify sanitary sewers, ____ is the international colour code used.

Green is the international colour code used to identify ____.

Copper chrome arsenate is most commonly used to treat ____.

____ stress can cause the lengthening of an object.

Every time joists are doubled, ____ must be used.

When using hardware fasteners on a permanent wood foundation, all fasteners must be ____.

____ is added to concrete to control the chemical reaction of the concrete with soil.

Interior non-load bearing masonry walls need a minimum footing of 200 mm wide for walls up to ____ m.

Interior non-load bearing masonry walls need a minimum footing of ____ mm wide for walls up to 5.5 metres.

What is the maximum nail spacing in mm for subfloors nailed at intermediate supports?

For proper support of wood frame structures, the top of grade beam elevation is required to be a minimum of ____ cm above the finished soil.

For proper support of wood frame structures, the top of grade beam elevation is required to be a minimum of 28 cm above the ____.

A concrete footing that supports a load bearing wall is called?

The cutting blade will rotate in a(n) ____ during normal operation of a router.

The best router for delicate inlay work is a ____ router.

____ firing in an air nailer requires a release and squeeze of the trigger each time it is fired.

When using an explosive actuated tool on steel, fasteners should not be driven closer than ____ mm from each other.

When using an explosive actuated tool on ____, fasteners should not be driven closer than 50 mm from each other.

The piston is protected by the ____ in an explosive actuated tool.

Explosive actuated tools are designed to work with the following materials. Select all that apply (3/5)

In order to create a flat surface on a board, a ____ should be used.

A side view of a cross cut saw will usually show ____ points per inch.

A side view of a ____ will usually show 8 points per inch.

Compressed air has the following characteristics. Select all that apply (4/6)

Hard Arkansas is a type of stone used to create a ____ edge on knives and woodworking tools.

An explosive actuated tool should never be used on which equipment? Select all that apply (3/5)

When using an explosive actuated tool with concrete, the fasteners should never be closer together than ____ mm.

When using an explosive actuated tool with ____, the fasteners should never be closer together than 75 mm.

In pneumatic tools the abbreviation ____ represents how much air can move per minute.

The lowest power level of an explosive actuated tool listed is ____.

Nail guns can be powered by the following. Select all that apply (4/5)

A ____ plane is used for one handed fitting and smoothing.

The blade of a plane is called a plane ____.

When using an explosive actuated tool the fastener point should penetrate ____ mm beyond the steel base material?

When using an explosive actuated tool the fastener point should penetrate 6 mm beyond this base material?

A 1/4 inch coupler and nipple can only be attached to an air tool equipped with a ____ inch air outlet.

An explosive actuated tool needs to be used on low velocity in order to be ____.

A laminate trimmer with a ____ is best for trimming corners.

Which sandpaper grit is often used between coats of paint or varnish?

A 200-400 grit sandpaper is best for ____.

What is the RPM of a drywall screw gun?

6000 RPM is the best speed for ____.

The grit of sandpaper most often used in tools is ____.

24-36 is a grit of sandpaper most often used for what application?

Which of the following are radial arm saw styles? Select all that apply (3/5)

Which of the following are not radial arm saw styles? Select all that apply (2/5)

A taper may form if the outfeed table on a jointer has been adjusted to be ____.

A ____ blade has flat top grind chippers and should never be used without both outside blades.

Referring to a hollow grind chisel, the primary bevel has an angle of ____ degrees.

The primary bevel on ____ chisel has an angle of 30 degrees.

Red represents the ____ charge on an explosive actuated tool.

A cove cutter is a router bit that creates a ____ edge.

____ is a term used describe the process of straightening the edges of lumber.

Referring to an all purpose twist drill bit, the lip clearance is ____ degrees.

Twelve degrees is the ____ clearance angle for an all purpose twist drill bit.

A bevel edge chisel would be chosen for ____.

On a circular saw blade the space between the teeth is referred to as a _____.

Classified as one of six classical simple machines, a ____ converts rotational motion, called torque, into up and down force.

A ____ line is used to keep a load from twisting in a single leg swing during hoisting.

A machine offset is best described as a ____.

Self-sealing screws are best used for ____.

Respirator face pieces are in which Class of CSA protection?

Class 7 CSA eye protection includes ____.

Which of the following is true about kiln dried lumber? Select all that apply (4/5)

Which of the following are characteristics of balsam fir? Select all that apply (4/5)

SPF grade lumber is made from which of the following? Select all that apply (3/5)

____ is a mixture of a deep red syrup and a light brown powder.

A ____ scaffold is not an acceptable type of scaffold.

The average drying period for lumber is ____.

The shortest possible drying time for lumber is ____.

The heartwood of a tree is used by the tree for ____.

A properly designed concrete mixture contains 10-15% cement, 60-75% aggregate and ____ water.

A properly designed concrete mixture contains 10-15% cement, ____ aggregate and 15-20% water.

A properly designed concrete mixture contains ____ cement, 60-75% aggregate and 15-20% water.

A properly designed concrete mixture contains which of the following? Select all that apply (3/5)

What are the basic components in concrete? Select all that apply (3/6)

Which of the following is true about stainless steel fasteners? Select all that apply (4/5)

Face shields are in which Class of CSA protection?

Class 6 CSA eye protection includes ____.

To find evidence of ambrosia beetles look for ____ in lumbar.

Which of the following are imperfections in wood? Select all that apply (4/5)

An MSDS for a controlled product must not be more than ____ years old.

An up to date ____ shall never exceed three years.

Which of the following are characteristics of red oak? Select all that apply (4/5)

Porosity, strength, durability and an open grain are characteristics of ____.

In reference to a portable fire extinguisher, what does the acronym PASS stand for? Select all that apply (4/5)

The PASS acronym applies to the ____.

How often do rigging components need to be inspected?

Examples of administrative controls are as follows? Select all that apply (4/5)

A test to measure the consistency of freshly mixed concrete is referred to as a ____ test.

A test to measure the ____ of freshly mixed concrete is referred to as a slump test.

____ cells radiate out horizontally from the centre of a tree outwards.

Concrete discharge must be complete within ____ minutes of mixing.

____ should be poured within 1.5 hours of being mixed.

Concrete that will be exposed to ____ cycles, is recommended to have air entrainment.

Concrete that will be exposed to freeze-thaw cycles, is recommended to have ____.

____ are a type of tree that shed their leaves.

A mitre joint is considered to be ____ degree joint.

A ____ joint is considered to be 45 degree joint.

A float base angle of ____ degrees to the hydraulic cylinder shaft is needed when setting up outriggers.

A ____ angle of 90 degrees to the hydraulic cylinder shaft is needed when setting up outriggers.

The first line of defense when fighting fires is ____.

The elimination of a hazard is an example of ____.

The angle between the legs of a sling and a horizontal plane is referred to as a ____ angle.

____ film is commonly used as a protective vapour barrier in applications.

A 9/16 inch diameter rope requires ____ U-bolt clip(s).

A ____ nail has a thin shaft with a small or non-existent head.

Which of the following wires of rope has the least wires per strand?

How are dangerously reactive materials classified under WHMIS?

On the job site, it is the responsibility of the workers to inspect their own PPE equipment ____.

Scaffolds need to be designed to be capable of safely supporting ____ times the load that may be imposed on it.

____ need to be designed to be capable of safely supporting four times the load that may be imposed on it.

The design and construction of a scaffold needs to be able to hold at least ____ times the maximum weight required for the job.