Carpenter – Second Period

A corner post needs to be ____ mm shorter than the measured wall to accommodate vinyl siding.

A corner post needs to be 6 mm shorter than the measured wall to accommodate ____.

On a 7/16 OSB sheeted roof, ____ are used between roof truss members.

On a 3/12 roof, the flashing around plumbing vents needs to extend ____ in all directions.

The drop to line of flight is ____.

When installing pocket doors it is important to ensure the following. Select all that apply (3/5)

In reference to a bifold door, the finished opening must be ____ mm plus the door width.

In reference to a bifold door, the finished opening must be 6 mm plus ____.

A roof panel has a stamp that reads “2R24.” The number or letter that represents that the panel’s horizontal edges must be supported is ____.

To properly install wood siding, the bottom should be at least ____ mm above finished grade.

To properly install wood siding, the bottom should be at least 200 mm above ____.

A two story house with a floor to floor measurement of 2540 mm has a unit rise for the stairs of 190 mm. The house requires ____ risers.

A ____ sits directly over a gable.

In reference to a bifold door, the finished opening must be ____ mm plus the door height.

In reference to a bifold door, the finished opening must be 19 mm plus ____.

The purpose of counter flashing is to ____.

A closed cornice can be described as follows. Select all that apply (4/6)

The minimum length of nails for joining a ledger strip to a wood beam is ____ mm.

Which of the following are true about ledger strips? Select all that apply (3/5)

The maximum unsupported height of an interior wall that does not have an attic accessible by a stairwell is three metres. The stud size is ____ mm.

____ framing is a type of framing where studs in multi-story buildings can be very long.

A carbon dioxide fire extinguisher is best used for ____.

If the joists or rafters in a load bearing wall are directly over or within ____ mm of the edge of the wall studs, single top plates may be used.

If the joists or rafters in a load bearing wall are directly over or within 50 mm of the edge of the wall studs, ____ may be used.

____ can be poured or blown into place.

A stub joist is a short joist that runs at ____ degrees to the regular joists.

A(n) ____ is a short joist that runs at 90 degrees to the regular joists.

The maximum unsupported height of a non-load bearing interior wall using a ____ stud size is 2.4 metres.

Safety footwear protection is divided into ____ grades.

There are 3 grades of ____ safety protection.

Which of the following are true about rigid insulation? Select all that apply (3/5)

Which of the following are true about cripple studs? Select all that apply (3/5)

When pump jack scaffolds utilize wood, they must be braced every ___ m.

Until guardrails can be reinstalled after being removed to allow for the hoisting of material, ____.

A nail is required to be the minimum length of ____ mm when adjoining a wall plate to a stud.

A nail is required to be the minimum length of 63 mm when adjoining a ____ to a stud.

Individual vertical framing members best describes a ____.

Which of the following are true about ceiling joists? Select all that apply (3/5)

A covered walkway needs to be at least ____ metres tall to protect the public from construction sites.

A ____ needs to be at least 2.5 metres tall to protect the public from construction sites.

Which of the following are true regarding propane and propane tanks. Select all that apply (3/5)

The maximum height for pump jack scaffolds using wood vertical posts is ____ m.

At the point of entry of a scaffold a ____ represents that the scaffold is safe for use.

Hazards within confined spaces can be which of the following? Select all that apply (4/5)

The resistance to heat transfer is greater, the higher the ____.

The metric equivalent of a ____ is 38 x 89.

A metal strap or plate of at least ____ mm must be nailed across across joists in single top plates in load bearing walls.

A ____ of at least 75 x 150 mm must be nailed across across joists in single top plates in load bearing walls.

Ten ____ is the minimum level of temporary light required for construction.

Construction hoarding is required when construction is not in an enclosed structure and is less than ____ meters from a sidewalk or public walkway.

The primary purpose of a construction hoarding is ____.

If a platform is higher than ____ meters, toe boards must be installed.

If a platform is higher than 3.5 metres, ____ must be installed.

An example of conduction is ____.

____ meter(s) is the maximum spacing allowed for ladders used in ladder jack scaffolding.

Three meters is the maximum spacing allowed for ____.

The purpose of wall sheathing membranes is ____.

The fastening of two lengths of 38 mm thick lumber is referred to as a ____.

A support beam or girder which acts as a secondary support member to an existing structure is called a ____.

If the height of a work platform does not exceed twice the shortest base dimension, only then it is safe to ____.

A non-load bearing stud requires a minimum of ____ of untouched material.

A ____ stud requires a minimum of 40 mm of untouched material.

A building method that relies on heavy timbers rather than dimensional lumber is ____.

To safety store ____, they must be in an upright position.

What is the minimum width of a light duty scaffold platform?

A scaffold should never be used in the following conditions. Select all that apply (5/6)

A minimum stud standard or #3 grade is needed for ____.

The metric equivalent of 38 x 89 is a ____?

In order to convert ____, multiply the larger unit of measurement by 25.4.