Carpenter – Red Seal

A ____ truss allows for full insulation at the perimeter.

To be eligible for R-2000 certification, air changes per hour (ACH) are required to be ____ or lower.

To be eligible for ____ certification, air changes per hour (ACH) are required to be 1.5 or lower.

A standard toilet will typically occupy ____ mm of space.

A standard ____ will typically occupy 750 mm of space.

Advanced framing is a method of framing a house that ____.

What is the recommended space that should be left above insulation in a bay window to keep a house warm?

A recommended space of 25 – 50 mm should be left ____ in a bay window to help keep a house warm.

It is estimated that ____% of the population suffer from some form of an allergy.

Many jurisdictions do not permit supply only exhaust systems because they ____.

Foundations must be able to be drilled for dowels, take rods and bolts when building an addition that ____.

It is estimated that 20% of the population suffer from ____.

Caulking that is ____ should never be used on builds for people who are hypersensitive to chemicals.

Measuring and laying out should be done with the backside of ____.

On a light duty scaffold, planks and platforms must not span more than ____ metres.

On a ____, planks and platforms must not span more than 3.1 metres.

Which of the following are characteristics of pre-manufactured wall panels. Select all that apply (4/5)

____ come in blueprint-matched, full widths, selectively reduced widths and sequence-matched uniform size set varieties.

When installing ____, it is common to place wooden strips between the flooring and the concrete.

Class D fire extinguishers should be located near ____.

The forefinger pointing up and rotating the hand in a circular motion best describes the ____ signal.

A non-grain raising stain has the following characteristics. Select all that apply (2/5)

Particle board, MDF, plywood and solid laminated wood are ____.

____ are fastened with glue to the frame and fasteners are placed in the top and bottom.

A baseboard should be mitred at ____ degree on an inside 90 degree corner.

A baseboard should be mitred at 44 degree on a(n) ____.

A standard space of ____ mm needs to be left open when installing a trash compactor in a cabinet.

A standard space of 306 mm needs to be left open when installing a(n) ____ in a cabinet.

Brushing on enough mineral spirits to wet a wooden surface is a good way to detect if any ____ is present.

When fastening material into a wall stud the fastener should penetrate ____ the thickness of the material being fastened.

When fastening trim, nails must be long enough to do the following. Select all that apply (3/5)

A journeyman carpenter can join the ____ program to be eligible to work their trade in other provinces.

____ plans start at the finished floor elevation and stop at the ceiling.

An ____ line is used to show the non hidden shape edges.

A t-square is the best tool for ____.

On a print the abbreviation “BS” means ____.

On a print the abbreviation “TYP” means ____.

On a print the abbreviation “WA” means ____.

On a print the abbreviation “RO” means ____.

Of the following pencil types, which is the darkest and softest grade?

9B refers to the ____.

The effort arm length compared to the resistance arm length is considered a(n) ____ type of advantage of a lever.

If your length is 3600 mm and your height is 1200 mm, then your diagonal is ____ rounded to the closest millimeter?

A floor plan can include the following. Select all that apply (4/5)

An actual 5 ft wall measures 1.25 inches on an imperial print. The scale the print uses is ____ equals one foot.

A three point drawing is used to show objects as ____.

The 12% deposit on a circular saw is $21.48. What is the full price of the saw?

The length of a diagonal used to square a building 25 feet by 41 feet is ____ feet.

Which of the following are included on a roof plan? Select all that apply (4/5)

If not reinforced, a ____ joint is the weakest type of joint.

A joint that enables the horizontal and vertical movement between two adjacent but separate members is called a ____ joint.

The best definition of sub base is ____.

The best definition of sub grade is ____.

A stamped certification mark must be present on all materials used on a ____.

Concrete blocks are available in sizes based on ____ mm increments.

____ are available in sizes based on 200 mm increments.

What is the maximum slump allowed for a concrete footing?

The ____ allowed in a concrete footing is 150 mm.

A builder must first consult a plot plan during the ____.

Loads resulting from the occurrence of temperature changes are an example of a(n) ____ load.

Regular joists are floor joists that ____.

Driveways and sidewalks that endure freeze/thaw cycles should use ____ concrete.

On the PWF certification stamp “L/B P/C CCA 1101”, which letters and/or numbers identify the preservative used?

Compression is the opposite of ___.

A block used to align the form bottom is called a ____.

Which of the following are true about headers. Select all that apply (4/5)

A concrete slab on ____ foundation is thickest on the outside perimeter.

A telepost supporting a beam is an example of a ____ load.

The certifying agency for lumber in Canada is ____.

The purpose of edge forms used for concrete sidewalks are which of the following? Select all that apply (2/5)

For a building that is 8900 wide by 11500 long with a 3 ply beam of 45 mm LVL material centered on the width. The floor system is anchored using a ladder at the top of a 200mm thick foundation wall. The clear span of the joists that are butted together over the beam rounded to the nearest millimetre is ____.

The National Building Code includes information on the following. Select all that apply (4/5)

An anchor bolt must have a thickness of no less than ____ mm in the foundation wall for a floor attachment frame.

A(n) ____ must have a thickness of no less than 12 mm in the foundation wall for a floor attachment frame.

To identify sanitary sewers, ____ is the international colour code used.

Green is the international colour code used to identify ____.

Copper chrome arsenate is most commonly used to treat ____.

____ stress can cause the lengthening of an object.

Every time joists are doubled, ____ must be used.

When using hardware fasteners on a permanent wood foundation, all fasteners must be ____.

____ is added to concrete to control the chemical reaction of the concrete with soil.

Interior non-load bearing masonry walls need a minimum footing of 200 mm wide for walls up to ____ m.

Interior non-load bearing masonry walls need a minimum footing of ____ mm wide for walls up to 5.5 metres.

What is the maximum nail spacing in mm for subfloors nailed at intermediate supports?

For proper support of wood frame structures, the top of grade beam elevation is required to be a minimum of ____ cm above the finished soil.

For proper support of wood frame structures, the top of grade beam elevation is required to be a minimum of 28 cm above the ____.

A concrete footing that supports a load bearing wall is called?

The cutting blade will rotate in a(n) ____ during normal operation of a router.

The best router for delicate inlay work is a ____ router.

____ firing in an air nailer requires a release and squeeze of the trigger each time it is fired.

When using an explosive actuated tool on steel, fasteners should not be driven closer than ____ mm from each other.

When using an explosive actuated tool on ____, fasteners should not be driven closer than 50 mm from each other.

The piston is protected by the ____ in an explosive actuated tool.

Explosive actuated tools are designed to work with the following materials. Select all that apply (3/5)

In order to create a flat surface on a board, a ____ should be used.

A side view of a cross cut saw will usually show ____ points per inch.

A side view of a ____ will usually show 8 points per inch.

Compressed air has the following characteristics. Select all that apply (4/6)

Hard Arkansas is a type of stone used to create a ____ edge on knives and woodworking tools.

An explosive actuated tool should never be used on which equipment? Select all that apply (3/5)

When using an explosive actuated tool with concrete, the fasteners should never be closer together than ____ mm.

When using an explosive actuated tool with ____, the fasteners should never be closer together than 75 mm.

In pneumatic tools the abbreviation ____ represents how much air can move per minute.

The lowest power level of an explosive actuated tool listed is ____.

Nail guns can be powered by the following. Select all that apply (4/5)

A ____ plane is used for one handed fitting and smoothing.

The blade of a plane is called a plane ____.

When using an explosive actuated tool the fastener point should penetrate ____ mm beyond the steel base material?

When using an explosive actuated tool the fastener point should penetrate 6 mm beyond this base material?

A 1/4 inch coupler and nipple can only be attached to an air tool equipped with a ____ inch air outlet.

An explosive actuated tool needs to be used on low velocity in order to be ____.

A laminate trimmer with a ____ is best for trimming corners.

Which sandpaper grit is often used between coats of paint or varnish?

A 200-400 grit sandpaper is best for ____.

What is the RPM of a drywall screw gun?

6000 RPM is the best speed for ____.

The grit of sandpaper most often used in tools is ____.

24-36 is a grit of sandpaper most often used for what application?

Which of the following are radial arm saw styles? Select all that apply (3/5)

Which of the following are not radial arm saw styles? Select all that apply (2/5)